If you're gonna do it, do it right. Here's our no-BS guide on how to lube your motorcycle chain properly every time.
It's everyone's favorite job to neglect: Lubing a motorcycle chain is easy to forget and even easier to ignore, but once your back end starts kinking and crunching, you'll know you dropped the ball one too many times.
With that being said, there's more to getting long life out of your motorcycle chain than simply spraying it down with lube every month or two. In fact, if all you're doing is lubing your chain every so often, you may be doing more harm than good.
Below we'll go over our tried-and-true procedure for how to properly service and lube a motorcycle chain every time. We'll also address some common questions and misinformation surrounding motorcycle chains as well, so make sure to check out our FAQ section for more info.
We keep a pretty large fleet in rotation here at Ride Adventures, and while a few of those are (thankfully) shaft-driven, the overwhelming majority of our rental bikes use chain final drives. Here's a step-by-step guide on how we keep those chains happy on all of our tours from Oregon to Thailand.
Got all that? Ok, let's dive in.
2. Prep Your Motorcycle
(If you don't have a stand of some kind, you can also just leave the bike on its side stand and work the chain in sections.)
3. Clean Both Your Chain and Rear Sprocket
The main killers of motorcycle chains are grit and rust. That means before we lay a finger on our lube, we need to get the chain scrubbed as clean as possible to remove any existing grit that's caked onto the links and rollers.
Start cleaning the chain by slipping your piece of cardboard behind the chain between the engine and rear axle. This will give you a "backboard" to catch all your cleaner and minimize the mess.
Whatever you're using, be liberal with it: Built-up grease doesn't like to come off on its own, and the more solvent you add to the equation, the easier it gets. Let the cleaner soak in for a moment, then get to scrubbing with your brush of choice.
Once your chain has been sprayed, scrubbed, and wiped clean, you're ready to lube up. Ideally, we always apply lube to a clean chain, because adding lubricant over existing dirt and grime just attracts more dirt and grime.
Rotate the wheel as you spray to ensure every link gets a good coat, and make sure to get a full rotation worth of lube on both the near and far faces of the links.
We've seen far too many riders simply blast lube down the center rollers of the chain, which does little to no good and mostly just wastes time and lube.
Once you're satisfied that both sides of the chain have been thoroughly lubed up, take a step back to admire your work and give your lube of choice a minute or so to soak in.
Once your lube has had a chance to set in, it's time to wipe it off. Yes, you read that right: this is one of the most common mistakes we see riders making when lubing a motorcycle chain.
While cleaning and lubricating your motorcycle's drive chain is one of the easiest maintenance items out there, there are still a ton of questions surrounding the procedure. Here's our take on the most commonly asked questions surrounding the topic.
The "standard" reply here is about every 500 miles, but remember, the main reason we lube a motorcycle chain in the first place is because it's just been cleaned. Pretty much every modern motorcycle nowadays runs a sealed O-ring chain (which is effectively self-lubricating), so you only really need to clean and lube your motorcycle chain whenever it's dirty or showing signs of surface rust.
Absolutely. WD40 is primarily made from a liquid hydrocarbon called "naphtha" which is commonly used as lantern or stove fuel in camping stoves. For all intents and purposes, naptha is essentially kerosene, and as such it works great for cleaning a chain. With that being said, WD40 is a solvent, not a lubricant, so you'll still want to lube your chain after cleaning it with WD40.
You've actually got a few good choices here. You can use a motorcycle-specific canned lube, generic gear oil, or a chain "paste" like Motul C5. Gear oil is a tried-and-true method as well as extremely affordable, while canned lube is quick and convenient but the quality varies by brand.
Depends on where you ride. In hot and dry climates like Southern California and Arizona where dust and grit are your main concerns, dry lube like Oxford Mint is ideal. In wetter climes, wet lubes offer better protection, and we've had good results with Maxima Chain Wax and Motul C5 paste. When in doubt, just stick with generic gear oil.
You'll find no shortage of opinions out there on this topic, but the best information we've found (and our own experience) suggests that the most important thing you can do for your chain is just keep it clean.
Motorcycle chain lube's primary purpose is to prevent rust from forming on the chain, so we wouldn't get too caught up in the "which brand is best" discussion.
With that being said, even the best-loved chains eventually call it quits. Whether they simply become too stretched and worn to continue using or begin kinking and binding as the factory grease fails and rust creeps in, at some point you'll need to replace both your chain and sprockets.
The that end, we've had our best experiences with D.I.D chains, and do our best to keep them in stock. We're particularly fond of D.I.D.'s X-ring chains (if they're good enough for Rossi, they're good enough for us), but even their classic O-Ring chains generally outlive any sprocket we wrap them around, so you really can't go wrong with any of their stuff.
D.I.D. Motorcycle Chains
Thanks for reading and we hope you learned a thing or two while also getting some maintenance out of the way on your beloved motorcycle.
→Read More: 6 Parking a Motorcycle: 6 Rookie Mistakes and Street & ADV Motorcycle Training.